A well-functioning toilet may seem like nothing, but for it to work well, homeowners have to take a lot of care on a daily basis. Needless to say, this routine care also includes mending some common toilet problems yourself.

If you have ever had a toilet issue such as a clogged bowl, running water, or a constantly refilling tank, you know how frustrating it can get.

Fortunately, many of these issues are easily fixable with the right tools and knowledge. Read on for our top 6 fixes to common toilet problems!

1. Clogged Toilet Bowls

The most common and troublesome of all toilet problems is the clogged bowl.

It is usually caused by flushing too much paper down the toilet at once. Basically, anything that is not biodegradable can clog the toilet eventually. Make it a point not to flush down anything that does not belong in the toilet. Head over to Inner City Plumbing if you'd like to know more about plumbing services.

The solution is to use a plunger to dislodge the blockage and restore your flow. If that doesn’t work, you may need an auger or snake tool to clear out the pipe further down.

These are useful tools to keep in your home plumbing kit. As you know, you may not always be able to reach your plumber. Then you can use these handy tools to solve the problem at hand.

If the clog persists, there is no choice but to call a blocked toilet specialist in Geelong.

2. Running Water

A constantly running toilet is annoying and expensive since it wastes money each time it runs.

The cause of this problem is often a worn-out flapper valve in the tank which needs replacement. It’s an easy fix that requires no plumbing experience or special tools!

3. Ghost Flushing

Ghost flushing means when your tank refills on its own after every flush, sometimes even without a flush. And strangely, there are no leaks in sight either!

It happens intermittently all day, and the reason for this is losing water either internally or externally. Check the toilet’s base for water puddles, which means the leak is external. But if you can’t see any, the leak is internal.

● Make sure the refill tube is inserted properly by checking it. Remove it if it is pushed too far into the overflow pipe and replace it on the outside of the overflow pipe.

● Look for any evident damage to the flapper. If it has, you have to replace the damaged flapper with a new one.

The above two solutions should fix the issue generally, but they don’t; you need to replace the complete flush with the help of a professional. Use a 24/7 Emergency Plumbing Service in Geelong if it needs immediate assistance.

4. Leaky Toilets

Leaking toilets are another nuisance and can cause water damage if left unchecked for too long.

These leaks often come from either loose connections between pipes or worn-out parts like washers or gaskets inside the tank, which will need replacing to stop any further leaking from occurring.

To fix this, you start by checking the flapper, which may be unsettled into the valve seat. The other causes may be a crack in the valve seat or a failed gasket. The leak would stop if you tighten the flapper or replace the gasket.

But if the water is overflowing from the tank, it is because the valve sits loosely. The fix is simple—screw it back firmly into its place.

5. Low Water Pressure

The weak water pressure coming from your toilet can be annoying at best and completely useless at worst!

The cause of this could range from a blockage in the pipes themselves to something as simple as air being trapped in them (which can happen if you haven’t used your toilet in a while).

You can fix this by checking if the water valve is fully open and opening it if not.

6. Water Level Drop in the Bowl

The general trick to find out if the toilet is functioning correctly is by checking the level of water in the bowl. If the water level is too high than usual, there can be only one problem—clogging.

But if it is too low, there are four potential problems—a damaged fill tube, cracked toilet bowl, faulty vent and a damaged fill valve.

This is what you do in this case:

● Lift the tank lid and check if the fill tube is displaced or broken. Replace it if it is broken, and reattach it if it’s still in good shape.

● Clean and remove any material that is obstructing the plumbing vent with a plumbing snake.

● Check the fill valve to confirm it is seated correctly and hasn’t suffered any damage. If it has a break or crack, you need to replace it with a different valve.

This is pretty much what you can do in case of a leaky toilet. For any other big issues, you have to call your plumber in Hoppers Crossing, as they are better aware of the situation.

Conclusion

These are some common problems you encounter with your toilets.

To keep your toilets in the best condition, you can also try other fixes, such as inspecting seals/washers for cracks, cleaning sediment buildup, checking float levels, and inspecting hoses for cracks or kinks!

The bottom line is to take regular care of the toilets in your home. Schedule regular maintenance with Your Local Plumbing, a plumbing company in Laverton.

Otherwise, they could end up creating a nuisance.

Toilets have many moving parts and components, which makes them prone to all kinds of issues over time—some more serious than others!

However, with just a little effort and some basic knowledge about how toilets work, you can fix most problems without having to call your plumber in Hoppers Crossing!

We hope this article has given you helpful tips on fixing some of those pesky toilet problems yourself!